Sapulpa, Oklahoma · Residential and Commercial
Sapulpa Spray Foam InsulationSpray foam insulation contractor for Creek County homes, shops and businesses
Sapulpa Spray Foam Insulation Kings installs open-cell and closed-cell spray foam in attics, crawl spaces, walls, garages and metal buildings from our base on 10th Street. We air seal and insulate in one step so Creek County homes and shops stay comfortable through hot Oklahoma summers and ice-storm winters.
- ✓Free estimates
- ✓Open-cell and closed-cell foam
- ✓Mon–Sat 8am–7pm, Sun 9am–2pm
✓ Free written estimates
✓ Based at 1216 10th St, Sapulpa, OK 74066
✓ Residential, commercial and new construction
✓ Sapulpa and surrounding areas
Spray foam insulation in Sapulpa
Insulation Solutions in Sapulpa Built for Oklahoma Weather
Sapulpa sits in climate zone 3A, where summers regularly pass 95°F with sticky humidity and winters bring hard freezes and the occasional ice storm. On a July afternoon an attic over a dark shingle roof can climb past 130°F. If your ductwork runs through that space, your air conditioner is fighting the attic as much as the sun, and the rooms at the end of the duct runs never quite cool off.
Spray foam insulation solves that at the source. Unlike fiberglass batts or loose fill, the foam expands to fill cracks, seams and gaps, bonds to the framing and creates an air barrier and an insulation layer in one application. Spray foam provides the thermal resistance of conventional insulation plus air sealing, which is why it performs so well in older Creek County houses that leak air at every top plate, wiring hole and attic hatch.
We are a Sapulpa spray foam insulation company working out of 1216 10th St, Sapulpa, OK 74066, a few blocks from downtown. We insulate everything from 1920s bungalows near the historic downtown and Route 66 to newer brick homes, metal shops on acreage toward Kellyville and Mounds, and commercial buildings along the highway corridors. Every spray foam insulation installation starts with a free estimate where we check for moisture, measure the area and explain whether open-cell foam, closed-cell foam or a cheaper insulation fits your home or building.
What we do
Sapulpa Spray Foam Insulation Services
Six services cover nearly every insulation problem we see in Sapulpa homes, shops and commercial buildings. Every one starts with a free estimate.
Attic Spray Foam Insulation
Open-cell or closed-cell foam on the attic roof deck keeps ductwork out of 130°F attic air and stops the heat that radiates through Sapulpa ceilings all summer.
Crawl Space Encapsulation
A sealed liner, closed-cell foam on the foundation walls and rim joists, and humidity control for pier-and-beam and crawl space homes that smell musty or have cold floors.
Wall Spray Foam Insulation
Open-cell or closed-cell foam for new construction, additions and gutted walls, filling every gap around wiring, outlets and top plates before the drywall goes up.
Metal Building Insulation
Closed-cell foam for steel shops, barndominiums, pole barns and commercial buildings that drip condensation on cool mornings and bake in July.
Garage Spray Foam Insulation
Spray foam for attached and detached garages and workshops, including the shared wall and the ceiling under bonus rooms, so the space stays usable year-round.
Spray Foam Roofing
Seamless spray polyurethane foam and a protective coating for flat and low-slope commercial roofs, adding insulation and a waterproof surface in one system.
Why spray foam
Benefits of Spray Foam Insulation for Sapulpa Homes
Spray foam insulation does more than add R-value. Here is what changes when the building envelope is sealed and insulated in one step.
Lower energy bills
ENERGY STAR estimates that sealing air leaks and adding insulation can cut heating and cooling costs by about 15 percent on average. Homes with leaky attics and ducts in the attic often see bigger energy savings.
Even temperatures
Back bedrooms, bonus rooms and rooms over the garage stop running several degrees hotter than the rest of the house because the attic and ducts stay near indoor temperature.
An air barrier, not just insulation
Foam fills the gaps around wiring, plumbing and top plates that fiberglass leaves open, so dust, pollen and humid outdoor air stay outside where they belong.
Moisture and condensation control
Closed-cell foam is a vapor retarder at about 1.5 inches. It stops condensation and the dripping roofs in metal shops and the damp air rising out of crawl spaces after Oklahoma rains.
Quieter rooms
Open-cell foam is excellent at dampening sound, which helps in homes near busy roads, between floors, and in home offices and media rooms.
Strength and longevity
Closed-cell foam adds racking strength to walls and roofs, and properly installed spray foam does not sag or settle, so it keeps working for decades.
Choosing the right foam
Open-Cell vs Closed-Cell Spray Foam
There are two types of spray foam insulation, and both air seal as they insulate. They behave very differently, so the right choice depends on where the foam goes.
| Feature | Open-Cell Spray Foam | Closed-Cell Spray Foam |
|---|---|---|
| R-value per inch | About R-3.5 to R-3.8 | About R-6 to R-7 (the highest R-value of any spray foam) |
| Density | About 0.5 lb per cubic foot, soft and flexible | About 2 lb per cubic foot, rigid |
| Air barrier | Yes, at about 3.5 inches | Yes, at about 1 inch |
| Moisture | Vapor permeable, can absorb water | Vapor retarder at about 1.5 inches |
| Strength | Adds no structural strength | Adds racking strength to walls and roofs |
| Sound | Excellent at dampening noise | Good |
| Best Sapulpa uses | Attic roof decks, interior and exterior walls | Crawl spaces, rim joists, metal buildings, garages, pole barns |
| Typical installed cost | About $0.45 to $0.80 per board foot | About $1.00 to $2.00 per board foot |
A board foot is one square foot at one inch thick. Read more in our honest look at spray foam pros and cons.
Spray foam vs fiberglass
Spray Foam vs Fiberglass and Blown-In Insulation
Fiberglass and cellulose slow heat flow, but air moves right through them and around every gap. In a typical Sapulpa house, leaks at top plates, recessed lights, plumbing stacks, rim joists and the attic hatch account for a large share of heating and cooling energy loss. That is why a home can have "enough" insulation on paper and still feel drafty in January and stuffy in August.
Spray foam fills those gaps as it goes on, so the insulation and the air barrier are one layer. It costs more per square foot than fiberglass batts or blown-in insulation, but in the places where air leakage and moisture are the real problems, it does a job the cheaper materials cannot.
Spray foam is not always the answer for home insulation. For an open attic floor with no ductwork, air sealing the ceiling and topping up with blown-in fiberglass or cellulose is usually the most cost-effective upgrade, and we will tell you when that is the case.
Where spray foam pays off most
- Attic roof decks with ductwork and an HVAC unit in the attic
- Walls in new construction and additions before drywall
- Crawl space foundation walls and rim joists
- Metal shops, barndominiums and pole barns that sweat
- Garages under bonus rooms and shared garage walls
- Flat commercial roofs that leak and lose heat
Pricing
Spray Foam Insulation Cost in Sapulpa
Spray foam insulation cost is based on board feet: the square footage sprayed times the thickness in inches. Open-cell foam typically runs about $0.45 to $0.80 per board foot installed, and closed-cell about $1.00 to $2.00. These are planning ranges for the Sapulpa area, and your free estimate replaces them with an exact written number.
Example 1: an attic roof deck of about 1,500 square feet with 5.5 inches of open-cell foam is 8,250 board feet, or roughly $3,700 to $6,600.
Example 2: a 30x40 metal shop with about 2 inches of closed-cell foam on the walls and roof commonly runs about $5,500 to $11,000, depending on wall height and doors.
What affects your price
- Square footage and foam thickness (total board feet)
- Open-cell vs closed-cell foam
- Access: tight attics, low crawl spaces and tall shop walls take longer
- Removing old insulation, nests or wet material first
- Prep and masking around equipment, windows and finished surfaces
- Code-required ignition or thermal barrier coatings
Why choose us
Why Sapulpa Chooses Spray Foam Insulation Kings
01
Based in Sapulpa
We work from 10th Street in Sapulpa, so estimates and follow-up visits across Creek County are close to home.
02
Free written estimates
Foam type, thickness, area and price in writing before any work starts, with no pressure to sign that day.
03
Moisture checked first
We never spray over wet decking or framing. Checking first prevents most of the problems that give spray foam a bad name.
04
Homes to commercial buildings
Attics, crawl spaces, walls, garages, metal shops, barndominiums and flat commercial roofs.
05
Honest recommendations
If blown-in insulation or fiberglass is the better value for part of your project, we say so and price it that way.
06
Open seven days a week
Monday through Saturday 8am to 7pm and Sunday 9am to 2pm, so you can reach us around a regular workday.
Service area
Spray Foam Insulation Near Me: Sapulpa and Surrounding Areas
From our base on 10th Street we cover all of Sapulpa, from the older homes around downtown and the Route 66 corridor to newer neighborhoods on the edges of town and rural property toward Sahoma Lake. We also serve the rest of Creek County, including Kellyville, Kiefer, Mounds and Bristow, and the west and south Tulsa metro: Glenpool, Sand Springs, Mannford, Jenks, Bixby and Tulsa.
Each community has its own insulation story, from Glenpool's two-story subdivisions to lake cabins around Mannford and pole barns on acreage near Kellyville. Pick your town for local notes and answers.
How it works
What to Expect From Our Spray Foam Installers
Call or request a quote
Tell us about the space, the building and any problems you have noticed. We set up a time for the free estimate.
On-site assessment
We inspect the area, check decking and framing for moisture, measure it and give you a written quote with foam type and thickness.
Prep and spray
We mask and protect the area, seal off living space, and spray in proper passes so the foam cures evenly.
Cure, cleanup and walkthrough
After curing and ventilation we clean up, trim overspray and walk through the work with you, with depth checks you can see.
From the blog
Spray Foam Insulation Tips and Guides for Sapulpa, OK
2026-10-02
Insulating a Historic Sapulpa Home Without Damaging Plaster Walls
You can make an older Sapulpa home far more comfortable without touching the plaster. Start with the attic, rim joists and crawl space, then weigh your wall options.
2026-10-02
What Balloon Framing Means for Insulating Older Sapulpa Houses
Balloon-framed houses have wall cavities that run from the foundation to the attic. Sealing and fire blocking those openings comes before any insulation.
2026-10-02
Crawl Space Encapsulation Cost in Sapulpa and When It Pays Off
Full crawl space encapsulation in Sapulpa usually costs about $3,500 to $7,500 for a 1,000 to 1,500 square foot crawl space. Here is what is included and when it pays off.
Frequently Asked Questions
Sapulpa Spray Foam Insulation FAQs
Straight answers to the questions Sapulpa-area property owners ask most. Still unsure? Call for a free consultation.
(918) 347-1793